|
|
|
|
Over View
| Features & Specification
| Actual Device List
|
|
Product : BeeProg2 |
|
|
 |
|
Multi Programming Systems - BeeProg2
Extremely fast universal USB/LPT interfaced programmer. If you're looking for lower
price universal programmer, please take a look at BeeProg+ programmer
Features :
GENERAL
- BeeProg2 programmer is practically identical with
the BeeProg+ programmer, difference is "only" much higher programming speed (20-70%)
of high-capacity memories, due to more powerful FPGA core inside.
- BeeProg2 is next member of USB/LPT-compatible, MS
Windows (from Windows 98 to Window 7 64-bit) based ELNEC universal programmers,
built to meet the strong demand of the small manufacturing and developers community
for the fast and reliable universal programmer.
- BeeProg2 programmer is based on the BeeProg+ programmer,
difference is only more powerful programming core inside.
- Supports all kinds of types and silicon technologies
of today and tomorrow programmable devices without family-specific module. You have
freedom to choose the optimal device for your design. Using built-in in-circuit
serial programming (ISP) connector, the programmer is able to program ISP capable
chips in circuit.
- BeeProg2 isn't only a programmer, but also a tester
of TTL/CMOS logic ICs and memories. Furthermore, it allows generation of user-definable
test pattern sequences.
- Provides very competitive price coupled with excellent
hardware design for reliable programming. Probably best "value for money"programmer
in this class.
- Extremely fast programming due to high-speed FPGA driven hardware and execution
of time-critical routines inside of the programmer. Tests show, is faster than competitors
in this category (status: 10/2009), for many chips much faster than most competitors.
As a result, when used in production this one-socket-programmer waits for an operator,
and not the other way round.
- BeeProg2 interfaces with the IBM PC compatible or higher, portable or desktop
personal computers through USB (2.0/1.1) port or any standard parallel (printer)
port. Programmer can utilize power of both USB high-speed port and IEEE1284 (ECP/EPP)
high-speed parallel port. Support of both USB/LPT port connection gives you the
choice to connect the BeeProg2 programmer to any PC, from latest notebook to older
desktop without USB port.
Specifications:
HARDWARE
Base unit, DACs
- USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate
- FPGA based IEEE 1284 slave printer port, up to 1MB/s transfer rate
- on-board intelligence: powerful microprocessor and FPGA based state machine
- three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
- VCCP range 0..8V/1A
- VPP1, VPP2 range 0..26V/1A
- autocalibration
- selftest capability
- protection against surge and ESD on power supply input, parallel port connection
- banana jack for ESD wrist straps connection
-
banana jack for connection to ground
ZIF socket, pindriver
- 48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up
to 48-pin
- pindrivers: 48 universal
- VCCP/VPP1/VPP2 can be connected to each pin
- perfect ground for each pin
- FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
- analog pindriver output level selectable from 1.8 V up to 26V
- current limitation, overcurrent shutdown, power failure shutdown
- ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
-
continuity test: each pin is tested before every programming operation
ISP connector
- 20-pin male type with missinsertion lock
- 6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from
1.8V up to 5V to handle all (low-voltage including) devices.
- 1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
- programmed chip voltage (VCCP) with both source/sink capability and voltage sense
- 1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
- target system supply voltage (range 2V..6V/250mA)
- ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
- two output signals, which indicate state of work result = LED OK and LED Error (active
level: min 1.8V)
-
input signal, switch YES! equivalent (active level: max 0.8V)
|
|
|
|
|
|
|
|
|
|
|
|
|
